Настоящие технические условия распространяются на трубы
"Изопро-флекс Арктик", "Изопрофлекс Арктик-У" (с каналом для
обогревающего кабе-ля) и "Изопрофлекс Арктик Комфорт" – с
обогревающим кабелем (далее – трубы), изготовленные из
полиэтиленовых труб по ГОСТ 18599, с теплоизо-ляцией из
пенополиуретана (ППУ) в гофрированной полиэтиленовой оболочке,
предназначенные для трубопроводов, транспортирующих воду, в том
числе хозяйственно-питьевого водоснабжения, при температуре
транспортируемой воды от 00 С до 400 С, а
также другие жидкости, к которым полиэтилен химически стоек.
ТУ 2248-019-40270293-2002
Стандарт
- формат doc
- размер 2.17 МБ
- добавлен 31 мая 2011 г.
Смотрите также
API Std 620 - 2002 Design and Construction of Large, Welded, Low-Pressure Storage Tanks (Eng)
Стандарт- формат pdf
- размер 1.96 МБ
- добавлен 18 января 2012 г.
American Petroleum Institute (API) Temth Edition, February 2002. 196p. This standard is based on the accumulated knowledge and experience of purchasers and manufacturers of welded, low-pressure oil storage tanks of various sizes and capacities for internal pressures not more than 15 pounds per square inch gauge. The object of this publication is to provide a purchase specification to facilitate the manufacture and procurement of such storage tank...
BS EN 12516-3: 2002 Valves - Shell design strength - Part 3: Experimental method (Eng)
Стандарт- формат pdf
- размер 252.79 КБ
- добавлен 17 декабря 2011 г.
This European Standard was approved by CEN on 1 August 2002. 16p. This standard establishes an experimental method of assessing the strength of valve shells by applying an elevated hydrostatic pressure test at room temperature.
BS EN 13445-2: 2002 Unfired pressure vessels - Part 2: Materials (Eng)
Стандарт- формат pdf
- размер 769.53 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 58p. This European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1:2002 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility. This document is not applicable in the creep range.
BS EN 13445-4: 2002 Unfired pressure vessels - Part 4: Fabrication (Eng)
Стандарт- формат pdf
- размер 759.32 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 60p. This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations.
BS EN 13480-1: 2002+A1: 2005 Metallic industrial piping - Part 1: General (Eng)
Стандарт- формат pdf
- размер 406.12 КБ
- добавлен 31 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. Amendment A1 was approved by CEN on 12 May 2005. 18p. This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials (but initially restricted to steel) with a view to ensure safe operation.
BS EN 13480-4: 2002 Metallic industrial piping - Part 4: Fabrication and installation (Eng)
Стандарт- формат pdf
- размер 361.44 КБ
- добавлен 31 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 48p. This Part of this European Standard specifies the requirements for fabrication and installation of piping systems, including supports, designed in accordance with EN 13480-3.
BS EN 13480-5: 2002 Metallic industrial piping - Part 5: Inspection and testing(Eng)
Стандарт- формат pdf
- размер 348.29 КБ
- добавлен 31 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 36p. This Part of this European Standard specifies the requirements for inspection and testing of industrial piping as defined in EN 13480-1:2002 to be performed on individual spools or piping systems, including supports, designed in accordance with EN 13480-3 and prEN 13480-6 (if applicable), and fabricated and installed in accordance with EN 13480-4.
BS EN 764-2: 2002 Pressure equipment - Part 2: Quantities, symbols and units (Eng)
Стандарт- формат pdf
- размер 130.38 КБ
- добавлен 21 декабря 2011 г.
This European Standard was approved by CEN on 29 April 2002. 10p. This European Standard specifies the basic quantities, symbols and units to be used for pressure equipment and assemblies addressed by the European Directive 97/23/EC.
BS EN 764-3: 2002 Pressure equipment - Part 3: Definition of parties involved (Eng)
Стандарт- формат pdf
- размер 111.09 КБ
- добавлен 21 декабря 2011 г.
This European Standard was approved by CEN on 29 April 2002. 8p. This European Standard defines terms and definitions of parties involved in the design, manufacture, testing and inspection of pressure equipment and assemblies addressed by the European Directive 97/23/EC
BS EN 764-7: 2002 Pressure equipment - Part 7: Safety systems for unfired pressure equipment (Eng)
Стандарт- формат pdf
- размер 726.59 КБ
- добавлен 21 декабря 2011 г.
This European Standard was approved by CEN on 29 April 2002. 42p. This European Standard specifies the requirements for safety systems which protect a vessel, a system of vessels, piping, accessories or assemblies from exceeding operating conditions. It is also applicable to safety related indicators and alarms, signals and warning devices when used in safety systems.