Стандарт
  • формат pdf
  • размер 1.96 МБ
  • добавлен 18 января 2012 г.
API Std 620 - 2002 Design and Construction of Large, Welded, Low-Pressure Storage Tanks (Eng)
American Petroleum Institute (API) Temth Edition, February 2002. 196p. This standard is based on the accumulated knowledge and experience of purchasers and manufacturers of welded, low-pressure oil storage tanks of various sizes and capacities for inteal pressures not more than 15 pounds per square inch gauge. The object of this publication is to provide a purchase specification to facilitate the manufacture and procurement of such storage tanks.
Смотрите также

API 510-2006 Pressure Vessel Inspection Code: In-Service Inspection, Rating, Repair, and Alteration

Стандарт
  • формат pdf
  • размер 848.62 КБ
  • добавлен 13 декабря 2011 г.
70 стр. Downstream Segment American Petroleum Institute, Ninth Edition , June 2006 General Application Coverage This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have been placed in service unless specifically excluded per 1.2.2. This incl...

API RP 2A-WSD-2007 Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms-Working Stress Design

Стандарт
  • формат pdf
  • размер 4.61 МБ
  • добавлен 13 декабря 2011 г.
288 стр. American Petroleum Institute, Errata And Supplement 3, October 2007 This publication serves as a guide for those who are concerned with the design and construction of new platforms and for the relocation of existing platforms used for the drilling, development, and storage of hydrocarbons in offshore areas. In addition, guidelines are provided for the assessment of existing platforms in the event that it becomes necessary to make a deter...

API RP 572-2009 Inspection Practices for Pressure Vessels

Стандарт
  • формат pdf
  • размер 2.53 МБ
  • добавлен 08 декабря 2011 г.
63 стр. THIRD EDITION, NOVEMBER 2009 This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reasons for inspection, causes of deterioration, frequency and methods of inspection, methods of repair, and preparation of re...

API Std 520-2008 Sizing, Selection, and Installation of Pressure-relieving Devices in Refineries: Part I-Sizing and Selection

Стандарт
  • формат pdf
  • размер 3.52 МБ
  • добавлен 08 декабря 2011 г.
148 стр. EIGHTH EDITION, DECEMBER 2008 This standard applies to the sizing and selection of pressure relief devices used in refineries and related industries for equipment that has a maximum allowable working pressure of 15 psig (103 kPag) or greater. The pressure relief devices covered in this standard are intended to protect unfired pressure vessels and related equipment against overpressure from operating and fire contingencies. This standard...

API Std 650 - 2001 Welded Steel Tanks for Oil Storage (Eng)

Стандарт
  • формат pdf
  • размер 1.94 МБ
  • добавлен 18 января 2012 г.
American Petroleum Institute (API) Temth Edition, November 1998. Addendum 2, November 2001. 240p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal pressures not exceeding the weight of the roof plates), but a higher interna...

API Std 653-2010 Tank Inspection, Repair, Alteration, and Reconstruction

Стандарт
  • формат pdf
  • размер 586.1 КБ
  • добавлен 08 декабря 2011 г.
44 стр. FOURTH EDITION, APRIL 2009 ADDENDUM 1, AUGUST 2010 This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction. The scope is limited to the tank foundation, bottom, shell, structure, roof, attached appurtenances, and nozzl...

ASME Section VIII div 3 2010.ASME Boiler and Pressure Vessel Code. Alternative Rules for Construction of High Pressure Vessels

Стандарт
  • формат pdf
  • размер 5.34 МБ
  • добавлен 31 октября 2011 г.
ASME Boiler and Pressure Vessel Code AN INTERNATIONAL CODE VIII Division 3 — Alternative Rules for Construction of High Pressure Vessels. Rules for Construction of Pressure Vessels. Date of Issuance: July 1, 2010 (Includes all Addenda dated July 2009 and earlier) 384 стр

BS EN 12952-2-2001 Water-tube boilers and auxiliary installations. Part 2. Materials for pressure parts of boilers and accessories

Стандарт
  • формат pdf
  • размер 262.43 КБ
  • добавлен 10 декабря 2011 г.
This European Standard was approved by CEN on 19 February 2001. 28p. This EN 12952-2 covers the requirements for the following materials for use in pressure parts of water-tube boilers and for parts welded on pressure parts

BS EN 13445-6: 2002+A1: 2004 Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheriodal graphite cast iron (Eng)

Стандарт
  • формат pdf
  • размер 753.72 КБ
  • добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002, and amendment A1 was approved by CEN on 9 February 2004. 38p. This European Standard specifies requirements for the design, materials, manufacturing and testing of pressure vessels and pressure vessel parts intended for use with a maximum allowable pressure, PS, equal or less 50 bar and shell wall thicknesses not exceeding 60 mm, that are constructed of spheroidal graphite cast iron.

NACE Standard RP0472-2005 Methods and Controls to Prevent In-Service Environmental Cracking of Carbon Steel Weldments in Corrosive Petroleum Refining Environments

Стандарт
  • формат pdf
  • размер 268.46 КБ
  • добавлен 09 декабря 2011 г.
17 стр. NACE International This standard establishes guidelines to prevent most forms of environmental cracking of weldments in carbon steel refinery equipment and piping. Weldments are defined to include the weld deposit, base metal HAZs, and adjacent base metal zones subject to residual stresses from welding. This standard covers only carbon steels classified as P-No. 1, Group 1 or 2. These classifications can be found in the ASME Boiler and Pr...