This European Standard was approved by CEN on 23 May 2002, and
amendment A1 was approved by CEN on 9 February 2004. 38p. This
European Standard specifies requirements for the design, materials,
manufacturing and testing of pressure vessels and pressure vessel
parts intended for use with a maximum allowable pressure, PS, equal
or less 50 bar and shell wall thicknesses not exceeding 60 mm, that
are constructed of spheroidal graphite cast iron.
BS EN 13445-6: 2002+A1: 2004 Unfired pressure vessels - Part 6: Requirements for the design and fabrication of pressure vessels and pressure parts constructed from spheriodal graphite cast iron (Eng)
Стандарт
- формат pdf
- размер 753.72 КБ
- добавлен 29 декабря 2011 г.
Похожие разделы
Смотрите также
API 510-2006 Pressure Vessel Inspection Code: In-Service Inspection, Rating, Repair, and Alteration
Стандарт- формат pdf
- размер 848.62 КБ
- добавлен 13 декабря 2011 г.
70 стр. Downstream Segment American Petroleum Institute, Ninth Edition , June 2006 General Application Coverage This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have been placed in service unless specifically excluded per 1.2.2. This incl...
API RP 572-2009 Inspection Practices for Pressure Vessels
Стандарт- формат pdf
- размер 2.53 МБ
- добавлен 08 декабря 2011 г.
63 стр. THIRD EDITION, NOVEMBER 2009 This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reasons for inspection, causes of deterioration, frequency and methods of inspection, methods of repair, and preparation of re...
API RP 572-2009 Inspection Practices for Pressure Vessels (With Annex A, B,C)
Стандарт- формат pdf
- размер 17.89 МБ
- добавлен 09 декабря 2011 г.
150 стр. c Приложениями Annex A (informative) Exchangers Annex B (informative) Towers Annex C (informative) Sample Record Forms THIRD EDITION, NOVEMBER 2009 This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reason...
API Std 520-2008 Sizing, Selection, and Installation of Pressure-relieving Devices in Refineries: Part I-Sizing and Selection
Стандарт- формат pdf
- размер 3.52 МБ
- добавлен 08 декабря 2011 г.
148 стр. EIGHTH EDITION, DECEMBER 2008 This standard applies to the sizing and selection of pressure relief devices used in refineries and related industries for equipment that has a maximum allowable working pressure of 15 psig (103 kPag) or greater. The pressure relief devices covered in this standard are intended to protect unfired pressure vessels and related equipment against overpressure from operating and fire contingencies. This standard...
ASME Section X 2010. ASME Boiler and Pressure Vessel Code. Fiber-Reinforced Plastic Pressure Vessels
Стандарт- формат pdf
- размер 3.93 МБ
- добавлен 31 октября 2011 г.
ASME Boiler and Pressure Vessel Code AN INTERNATIONAL CODE X Fiber-Reinforced Plastic Pressure Vessels. Rules for Construction of Pressure Vessels. Date of Issuance: July 1, 2010 (Includes all Addenda dated July 2009 and earlier) 266 стр
BS EN 13445-1: 2009 Unfired pressure vessels - Part 1: General (Eng)
Стандарт- формат pdf
- размер 235.77 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 30 June 2009. 44p. This European Standard defines the terms, definitions, quantities, symbols and units that are used throughout the EN 13445. It also contains instructions on how to use the standard (Annex A) as well as an index which covers the whole standard (Annex B). This information is aimed to aid the user of the EN 13445. This European Standard applies to unfired pressure vessels with a maximu...
BS EN 13445-2: 2002 Unfired pressure vessels - Part 2: Materials (Eng)
Стандарт- формат pdf
- размер 769.53 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 58p. This European Standard specifies the requirements for materials (including clad materials) for unfired pressure vessels and supports which are covered by EN 13445-1:2002 and manufactured from metallic materials; it is currently limited to steels with sufficient ductility. This document is not applicable in the creep range.
BS EN 13445-4: 2002 Unfired pressure vessels - Part 4: Fabrication (Eng)
Стандарт- формат pdf
- размер 759.32 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 60p. This document specifies requirements for the manufacture of unfired pressure vessels and their parts, made of steels, including their connections to non-pressure parts. It specifies requirements for material traceability, manufacturing tolerances, welding requirements, production tests, forming requirements, heat treatment, repairs and finishing operations.
BS EN 13445-5: 2002 Unfired pressure vessels - Part 5: Inspection and testing (Eng)
Стандарт- формат pdf
- размер 773.18 КБ
- добавлен 29 декабря 2011 г.
This European Standard was approved by CEN on 23 May 2002. 82p. This European Standard specifies the inspection and testing of individual and serially produced pressure vessels made of steels in accordance with EN 13445-2 subject to predominantly non_cyclic operation (i.e. vessels operating below 500 full equivalent pressure cycles).
BS EN 764-7: 2002 Pressure equipment - Part 7: Safety systems for unfired pressure equipment (Eng)
Стандарт- формат pdf
- размер 726.59 КБ
- добавлен 21 декабря 2011 г.
This European Standard was approved by CEN on 29 April 2002. 42p. This European Standard specifies the requirements for safety systems which protect a vessel, a system of vessels, piping, accessories or assemblies from exceeding operating conditions. It is also applicable to safety related indicators and alarms, signals and warning devices when used in safety systems.