Casing/Tubing design manual october 2005 Chevron
Подождите немного. Документ загружается.
Table 5-24 XLF (XL Systems/ Grant-Prideco
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5°
Load Flank Angle
-10°
Thread Height 1.905 mm 0.075 in. 1.905 mm 0.075 in.
Nominal Lead (Average) 19.05 mm 0.750 19.05 mm 0.750
Pitch (Average) 19.05 mm 0.750 19.05 mm 0.750
Nominal Taper (Diameter) 0.600 (average)
Type Integral joint (flush)
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class (4-4)
Available Sizes 406.40 mm (16.000 in.)-1828.80 mm (72.000 in.)
Comments
Figure 5-21 XLF
5-36 Casing/Tubing Design Manual
October 2005
Table 5-25 501 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.27 mm 0.05 in. 1.27 mm 0.05 in.
Nominal Lead 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Pitch 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Nominal Taper (Diameter) 0.08
Type Integral joint (external upset pipe)
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class (4-2)
Available Sizes 60.32 mm (2.375 in.)-114.30 mm (4.500 in.)
Comments 501, 531 and 561 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-22 501
Casing/Tubing Design Manual 5-37
October 2005
Table 5-26 503 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.27 mm 0.05 in. 1.27 mm 0.05 in.
Nominal Lead 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Pitch 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Nominal Taper (Diameter) 0.08
Type Integral joint (external upset pipe)
Primary Seal Metal-to-metal (cone-on-cone)
Location of Torque Shoulder Thread flanks
Class (3-2)
Available Sizes 127.00 mm (5.000 in.)-193.68 mm (7.625 in.)
Comments 503, 533 and 563 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-23 503
5-38 Casing/Tubing Design Manual
October 2005
Table 5-27 511 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.016-
2.540 mm
0.04 -
0.10 in.
1.016-
2.540 mm
0.04 -
0.10 in.
Nominal Lead 6.198 to
10.82 mm
0.244 to
0.426 in.
6.198 to
10.82 mm
0.244 to
0.426 in.
Pitch 6.198 to
10.82 mm
0.244 to
0.426 in.
6.198 to
10.82 mm
0.244 to
0.426 in.
Nominal Taper (Diameter) 0.06-0.12
Type Integral joint (flush)
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class 4-3
Available Sizes 52.40 mm (2.063 in.)-301.62 mm (11.875 in.)
Comments Compression to tension efficiency ratio is 1.16 to
1.35 (1.21 average).
Figure 5-24 511
Casing/Tubing Design Manual 5-39
October 2005
Table 5-28 521 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.27-
2.54 mm
0.05 -
0.10 in.
1.27-
2.54 mm
0.05 -
0.10 in.
Nominal Lead 7.569 to
10.82 mm
0.298 to
0.426 in.
7.569 to
10.82 mm
0.298 to
0.426 in.
Pitch 7.569 to
10.82 mm
0.298 to
0.426 in.
7.569 to
10.82 mm
0.298 to
0.426 in.
Nominal Taper (Diameter) 0.08-0.12
Type Integral joint (non-upset pin w/swaged OD box)
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class 4-2
Available Sizes 101.60 mm (4.000 in.)-473.08 mm (18.625 in.)
Comments Compression to tension efficiency ratio is 1.11 to
1.37 (1.22 average).
Figure 5-25 521
5-40 Casing/Tubing Design Manual
October 2005
Table 5-29 531 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.27 mm 0.05 in. 1.27 mm 0.05 in.
Nominal Lead 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Pitch 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Nominal Taper (Diameter) 0.08
Type Integral joint (internal/external upset pipe)
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class 4-2
Available Sizes 60.32 mm (2.375 in.)-114.30 mm (4.500 in.)
Comments 501, 531 and 561 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-26 531
Casing/Tubing Design Manual 5-41
October 2005
Table 5-30 533 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.270-
2.032 mm
0.05 -
0.08 in.
1.270-
2.032 mm
0.05 -
0.08 in.
Nominal Lead 7.366 to
9.246 mm
0.290 to
0.364 in.
7.366 to
9.246 mm
0.290 to
0.364 in.
Pitch 7.366 to
9.246 mm
0.290 to
0.364 in.
7.366 to
9.246 mm
0.290 to
0.364 in.
Nominal Taper (Diameter) 0.08
Type Integral joint (internal/external upset pipe)
Primary Seal Metal-to-metal (cone-on-cone)
Location of Torque Shoulder Thread flanks
Class 2-2
Available Sizes 60.32 mm (2.375 in.) -193.68 mm (7.625 in.)
Comments 503, 533 and 563 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-27 533
5-42 Casing/Tubing Design Manual
October 2005
Table 5-31 561 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.27 mm 0.05 in. 1.27 mm 0.05 in.
Nominal Lead 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Pitch 7.366 mm 0.290 in. 7.366 mm 0.290 in.
Nominal Taper (Diameter) 0.08
Type Threaded and coupled
Primary Seal Thread lubricant
Location of Torque Shoulder Thread flanks
Class (4-1)
Available Sizes 60.32 mm (2.375 in.)-114.30 mm (4.500 in.)
Comments 501, 531 and 561 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-28 561
Casing/Tubing Design Manual 5-43
October 2005
Table 5-32 563 (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
-5° to -10°
Load Flank Angle
-5° to -10°
Thread Height 1.270-
2.032 mm
0.05-
0.08 in.
1.270-
2.032 mm
0.05-
0.08 in.
Nominal Lead 7.569 to
10.82 mm
0.298 to
0.426 in.
7.569 to
10.82 mm
0.298 to
0.426 in.
Pitch 7.569 to
10.82 mm
0.298 to
0.426 in.
7.569 to
10.82 mm
0.298 to
0.426 in.
Nominal Taper (Diameter) 0.08-0.12
Type Threaded and coupled
Primary Seal Metal-to-metal (cone-on-cone)
Location of Torque Shoulder Thread flanks
Class 2-1
Available Sizes 60.32 mm (2.375 in.)-177.80 mm (7.000 in.)
Comments 503, 533 and 563 are interchangeable in the same
size and weight combinations.
Compressive strength is 100% of pipe body.
Figure 5-29 561
5-44 Casing/Tubing Design Manual
October 2005
5.9 References
1. Wu, Jiang: “Guideline for Selection of Threaded Connections for Casing and
Tubing,” Chevron EPTC Tech Memo #2002-08, Houston, Texas, (July 2002).
2. VAM Catalog No. 940, VAM-PTS (May 2000).
3. High Performance Tubular Products Catalog 001, Hydril
®
(2000).
4. Product Catalog, Hunting Interlock.
5. Atlas Bradford Premium Connections, Grant-Prideco
®
(December 2000).
Casing/Tubing Design Manual 5-45
October 2005