Casing/Tubing design manual october 2005 Chevron
Подождите немного. Документ загружается.
Table 5-14 GB-TCC (GB Tubulars)
Pin Box
Metric English Metric English
Stab Flank Angle
+10°
Load Flank Angle
+3°
Thread Height 1.575 mm 0.062 in. 1.575 mm 0.062 in.
Nominal Lead 5.080 mm 0.200 in. 5.080 mm 0.200 in.
Pitch 5.080 mm 0.200 in. 5.080 mm 0.200 in.
Nominal Taper (Diameter) 0.0625 for sizes < 346.08 mm (13.625 in.)
0.0833 for sizes ≥ 406.40 mm (16 in.)
Type Threaded and Coupled
Primary Seal Thread lubricant
Location of Torque Shoulder N/A (optional)
Class (4-3)
Available Sizes All API sizes
Comments Special clearance (S.C.) and internal shoulder (I.S.)
versions are also available.
Compression to tension efficiency ratio is 1.00
Figure 5-11 GB-TCC
5-26 Casing/Tubing Design Manual
October 2005
Table 5-15 HDL (Grant-Prideco
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
+25°
Load Flank Angle
-7.5° - -13°
Thread Height 0.813-
1.270 mm
0.032-
0.050 in.
0.813-
1.270 mm
0.032-
0.050 in.
Nominal Lead 4.242-
5.080 mm
0.167-
0.200 in.
4.242-
5.080 mm
0.167-
0.200 in.
Pitch 4.242-
5.080 mm
0.167-
0.200 in.
4.242-
5.080 mm
0.167-
0.200 in.
Nominal Taper (Diameter) 0.0625-0.1458
Type Integral flush joint
Primary Seal
Base and end of pin (5°)
Location of Torque Shoulder
Base of pin, 0°
Class 2-3
Available Sizes 60.32 mm (2.375 in.)-339.72 mm (13.375 in.)
Comments
Figure 5-12 HDL
Casing/Tubing Design Manual 5-27
October 2005
Table 5-16 New VAM (Vallourec, VAM PTS, Sumitomo)
Pin Box
Metric English Metric English
Stab Flank Angle
+10°
Load Flank Angle
+3°
Thread Height 1.016 mm 0.040 in. 1.016 mm 0.040 in.
Nominal Lead 3.175 mm (0.125 in.) for 60.32 mm (2.375 in.),
73.02 mm (2.875 in.)
4.233 mm (0.167 in.) for 88.90 mm (3.500 in.),
101.60 mm (4.000 in.), 114.30 mm (4.500 in.)
5.080 mm (0.200 in.) for 125.00 mm (5.000 in.) and
higher
Pitch Same as taper
Nominal Taper (Diameter) 0.0625
Type Threaded and coupled
Primary Seal Metal-to-metal (10% taper on diameter for casing,
30° chamfer for tubing)
Location of Torque Shoulder
End of pin, 15° casing, 20° tubing
Class 3-2
Available Sizes 60.32 mm (2.375 in.)-339.72 mm (13.375 in.)
Comments
Figure 5-13 New VAM
5-28 Casing/Tubing Design Manual
October 2005
Table 5-17 ACE (Vallourec, VAM PTS, Sumitomo)
Pin Box
Metric English Metric English
Stab Flank Angle
+10°
Load Flank Angle
-3°
Thread Height 1.575 mm 0.062 in. 1.575 mm 0.062 in.
Nominal Lead 3.175 mm (0.125 in.) for 60.32 mm (2.375 in.),
73.02 mm (2.875 in.)
4.233 mm (0.167 in.) for 88.90 mm (3.500 in.),
101.60 mm (4.000 in.), 114.30 mm (4.500 in.)
5.080 mm (0.200 in.) for 125.00 mm (5.000 in.)-
193.68 mm (7.625 in.)
6.350 mm (0.250 in.) for 219.08 mm (8.625 in.) and
higher
Pitch Same as lead
Nominal Taper (Diameter) 0.0625
Type Threaded and coupled
Primary Seal Metal-to-metal
Location of Torque Shoulder
End of pin, -15°
Class 2-2
Available Sizes 60.32 mm (2.375 in.)-114.30 mm (4.500 in.)
Comments
Figure 5-14 ACE
Casing/Tubing Design Manual 5-29
October 2005
Table 5-18 ANJO (Grant-Prideco
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
+25°
Load Flank Angle
-7.5° - -10°
Thread Height 1.041-
1.575 mm
0.041-
0.062 in.
1.041-
1.575 mm
0.041-
0.062 in.
Nominal Lead 4.234-6.35
mm
0.1667-
0.25 in.
4.234-6.35
mm
0.1667-
0.25 in.
Pitch 4.234-6.35
mm
0.1667-
0.25 in.
4.234-6.35
mm
0.1667-
0.25 in.
Nominal Taper (Diameter) 0.0625
Type Integral joint (swaged)
Primary Seal Metal-to-metal
Location of Torque Shoulder
Middle, -15°
Class 3-3
Available Sizes 114.30 mm (4.500 in.)-346.08 mm (13.625 in.)
Comments
Figure 5-15 ANJO
5-30 Casing/Tubing Design Manual
October 2005
Table 5-19 PH4/6 (Hydril
®
, Benoit, Grant-Prideco
®
, Halliburton, Hub City, Oilfield
Mfg., Technitube Rohrenwerke, TTI)
Pin Box
Metric English Metric English
Stab Flank Angle
15° to 25°
Load Flank Angle
5° to 8°
Thread Height 0.762-
1.778 mm
0.03-
0.07 in.
0.762-
1.778 mm
0.03-
0.07 in.
Nominal Lead 3.175 to
6.350 mm
0.125 to
0.250 in.
3.175 to
6.350 mm
0.125 to
0.250 in.
Pitch 3.175 to
6.350 mm
0.125 to
0.250 in.
3.175 to
6.350 mm
0.125 to
0.250 in.
Nominal Taper (Diameter) Cylindrical
Type Integral joint (upset)
Primary Seal Metal-to-metal (cone-on-cone)
Location of Torque Shoulder
Base of pin, -30°
Class 2-2
Available Sizes 60.32 mm (2.375 in.)-114.30 mm (4.500 in.)
Comments Compression to tension efficiency ratio is 1.0.
Figure 5-16 PH4/6
Casing/Tubing Design Manual 5-31
October 2005
Table 5-20 Seal-Lock HC (Hunting-Interlock)
Pin Box
Metric English Metric English
Stab Flank Angle
+45° - +18°
Load Flank Angle
-10° - -3°
Thread Height 0.9855-
1.290 mm
0.0388-
0.0508 in.
1.240-
1.494 mm
0.0488-
0.0588 in.
Nominal Lead 5.080 mm 0.200 in. 5.080 mm 0.200 in.
Pitch 5.080 mm 0.200 in. 5.080 mm 0.200 in.
Nominal Taper (Diameter) 0.1042
Type Threaded and coupled
Primary Seal Metal-to-metal
Location of Torque Shoulder End of pin
Class 3-2
Available Sizes 114.30 mm (4.500 in.)-346.08 mm (13.625 in.)
Comments
Figure 5-17 Seal-Lock HC
5-32 Casing/Tubing Design Manual
October 2005
Table 5-21 SLX (Hydril
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
15° to 25°
Load Flank Angle
-10° to -15°
Thread Height 1.016-
1.778 mm
0.04-
0.07 in.
1.016-
1.778 mm
0.04-
0.07 in.
Nominal Lead 3.175 to
5.639 mm
0.125 to
0.222 in.
3.175 to
5.639 mm
0.125 to
0.222 in.
Pitch 3.175 to
5.639 mm
0.125 to
0.222 in.
3.175 to
5.639 mm
0.125 to
0.222 in.
Nominal Taper (Diameter) Cylindrical or 0.120
Type Integral joint (formed ends)
Primary Seal Metal-to-metal (cone-on-cone)
Location of Torque Shoulder Middle, negative angle
Class 2-3
Available Sizes 114.3 mm (4.500 in.)-346.08 mm (13.625 in.)
Comments Connection OD is 1.5-2 % of tube OD
Compression to tension efficiency ratio is 0.50.
Figure 5-18 SLX
Casing/Tubing Design Manual 5-33
October 2005
Table 5-22 STL (Grant-Prideco
®
)
Pin Box
Metric English Metric English
Stab Flank Angle
+45°
Load Flank Angle
-9°
Thread Height 1.016 mm 0.04 in. 1.016 mm 0.04 in.
Nominal Lead 5.08 mm 0.2 in. 5.08 mm 0.2 in.
Pitch 10.16 mm 0.4 in. 10.16 mm 0.4 in.
Nominal Taper (Diameter) 0.0625-0.09375
Type Integral joint (flush)
Primary Seal Metal-to-metal
Location of Torque Shoulder
Base of pin, -15°
Class 2-4
Available Sizes 60.32 mm (2.375 in.)-346.08 mm (13.625 in.)
Comments Compression to tension efficiency ratio is 0.60.
Figure 5-19 STL
5-34 Casing/Tubing Design Manual
October 2005
Table 5-23 VAM HW (Vallourec, VAM PTS, Sumitomo)
Pin Box
Metric English Metric English
Stab Flank Angle
+10°
Load Flank Angle
-3°
Thread Height 1.981-
2.388 mm
0.078-
0.094 in.
1.981-
2.388 mm
0.078-
0.094 in.
Nominal Lead 6.350 mm 0.25 in. 6.350 mm 0.25 in.
Pitch 6.350 mm 0.25 in. 6.350 mm 0.25 in.
Nominal Taper (Diameter) 0.125 0 0.1817
Type Thread and Coupled
Primary Seal Metal-to-Metal (10% taper on diameter)
Location of Torque Shoulder End of pin
Class (3-2)
Available Sizes 127.0 mm (5.000 in.)-355.60 mm (14.000 in.)
Comments
Figure 5-20 VAM HW
Casing/Tubing Design Manual 5-35
October 2005