Bednar H.H. Pressure vessel design handbook

Справочник

формат pdf
размер 18.07 МБ
добавлен 14 января 2012 г.

Bednar H.H. Pressure vessel design handbook

Handbook, 2nd edition
Krieger Publishing Compane, 1986. - 431 p.

Design loads
Stress categories and design limit stresses
Membrane stress analysis of vessel shell components
Design of tall cylindrical self-supporting prosess columns
Supports for short vertical vessels
Design of saddle supports for large horizontal cylindrical pressure vessels
Local stresses in slells due to loads on attachments
Discontinuity stresses
Thermal stresses
Weld design
Selection of construction materials
Numerical methods for stress analysis of axisymmetric shells

Смотрите также

Bunch J.O., Mitchel M.R. (editors) Residual Stress Effects on Fatigue and Fracture Testing and Incorporation of Results Into Design

Статья

формат pdf
размер 5.22 МБ
добавлен 04 декабря 2011 г.

ASTM special technical publication, STP 1497. 164 р. This publication, Residual Stress Effects on Fatigue and Fracture Testing and Incorporation of Results into Design, contains papers presented at the Symposium on Residual Stress, which was held in Salt Lake City, UT on 19-20 May, 2004. The symposium was sponsored by ASTM International Committee E08 on Fatigue and Fracture. Dr. Jeffrey O. Bunch, Boeing Integrated Defense Systems, presided as sy...

Chopra O.K., Alexandreanu B., and Shac W.J. Effect of Material Heat Treatment on Fatigue Crack Initiation in Austenitic Stainless Steels in LWR Environments

формат pdf
размер 22.86 МБ
добавлен 04 декабря 2011 г.

65 стр. Office of Nuclear Regulatory Research U.S. Nuclear Regulatory Commission Washington, DC 20555–0001 The ASME Boiler and Pressure Vessel Code provides rules for the design of Class 1 components of nuclear power plants. Figures I–9.1 through I–9.6 of Appendix I to Section III of the Code specify design curves for applicable structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly address...

Koliar L.P. Mechanics of composite structures

формат pdf
размер 33.06 МБ
добавлен 12 ноября 2010 г.

Cambridge University Press, 2003. - 480 p. The increased use of composites in aerospace, land, and marine applications has resulted in a growing demand for engineers versed in the design of structures made of fiber-reinforced composite materials. To satisfy this demand, and to introduce engineers to the subject of composites, numerous excellent texts have been published dealing with the mechanics of composites. These texts deal with those fndame...

Liu A.F. Mechanics and Mechanisms of Fracture: An Introduction

формат pdf
размер 22.76 МБ
добавлен 20 января 2012 г.

ASM International, 2005, ISBN: 0871708027, 458 pages This text is for readers who want an introductory overview on the mechanical and material factors of fracture in design analysis, material evaluation, and failure prevention. Both fundamental and practical concepts of fracture are described in terms of stress analysis and the mechanical behavior of materials. The metallurgical aspects of deformation and fracture in metals are also discussed....

Schwam David, Wallace John F. Effect of design factors on thermal fatique cracking of die casting dies

формат pdf
размер 1.87 МБ
добавлен 04 декабря 2011 г.

102 стр. 2004 г. Department of Materials Science Case Western Reserve University Cleveland, Ohio Work Performed Under Contract DE-FC07- 00ID138486 US Department of Energy Assistant Secretary for Energy Efficiency and Renewable Energy Washington DC This research investigation was supported by the Department of Energy, Office of Industrial Technology through the Cast Metal Coalition program. The Die Materials Committee of the North American...

Singh R.K. (ed.). Weld Cracking in Ferrous Alloys

формат pdf
размер 9.37 МБ
добавлен 01 января 2012 г.

Woodhead Publishing Limited, 2009. - 562 pages Weld cracks are unacceptable defects that can compromise the integrity of welded structures. Most cracks are the result of solidification, cooling and stresses that develop due to weld shrinkage. Weld cracking can lead to structural failures which at best will require remedial action and at worst can lead to loss of life. All industries that utilize welding can be affected, including nuclear, aerospa...

Wu H.-Ch. Continuum Mechanics and Plasticity

формат pdf
размер 7.08 МБ
добавлен 22 ноября 2011 г.

Монография. Boca Raton: CHAPMAN & HALL, 2004. – 685 с. Tremendous advances in computer technologies and methods have precipitated a great demand for refinements in the constitutive models of plasticity. Such refinements include the development of a model that would account for material anisotropy and produces results that compare well with experimental data. Key to developing such models-and to meeting many other challenges in the field- is a...