ASTM D 4175-05. Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants

220 стр. ELEVENTH EDITION, SEPTEMBER 2010 ERRATA, JULY 2011 ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-b...

48 стр SDO: API: American Petroleum Institute This International Standard is based on API RP 5A3, first edition, June 1996. This International Standard specifies requirements and gives recommendations for the manufacture, testing and selection of thread compounds for use on casing, tubing and line pipe based on the current industry consensus of good engineering practice. It is intended that the words casing and tubing apply to the service applica...

20 cтр. API SPECIFICATION Q1 SIXTH EDITION, MARCH 1, 1999 EFFECTIVE DATE: SEPTEMBER 1, 1999 API Specification Ql provides requirements for a quality system that may be applied on an international basis to facilitate the consistent and reliable manufacture of products to specifications prepared for the oil and gas industry. Part One of this Standard is aligned with ANSI/ISO/ASQC Q9001- 1994, Quality Systems—Model for Quality Assurance in Design, D...

American Petroleum Institute / 01-Sep-2010 / 220 pages. Edition: 11th. Eleventh Edition (ISO 13709:2009 Identical Adoption). Scope. This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to overhung pumps, between-bearings pumps and vertically s...

220 стр. ANSI/API STANDARD 610 ELEVENTH EDITION, SEPTEMBER 2010 ERRATA, JULY 2011 ISO 13709:2009 (Identical), Centrifugal pumps for petroleum, petrochemical and natural gas industries This International Standard specifies requirements for centrifugal pumps, including pumps running in reverse as hydraulic power recovery turbines, for use in petroleum, petrochemical and gas industry process services. This International Standard is applicable to ove...

234 стр. Current status: Active Short description: Covers the minimum requirements for centrifugal compressors used in petroleum, chemical, and gas industry services that handle air or gas, including process gear mounted. Does not apply to fans or blowers that develop less than 34 kPa (5 pounds per square inch) pressure rise above atmospheric pressure; these are covered by API Standard 673. This standard also does not apply to packaged, integrall...

167 стр. API STANDARD 618 FOURTH EDITION, JUNE 1995 This standard covers the minimum requirements for reciprocating compressors and their drivers used in petroleum, chemical, and gas industry services for handling process air or gas with either lubricated or nonlubricated cylinders. Compressors covered by this standard are of mod- erate-to-low speed and in critical services. Also covered are related lubricating systems, controls, instrumentation,...

API STANDARD 618 FIFTH EDITION, DECEMBER 2007 This standard is based on the accumulated knowledge and experience of manufacturers and users of reciprocating compressors. The objective of this publication is to provide a purchase specification to facilitate the procurement and manufacture of reciprocating compressors for use in petroleum, chemical, and gas industry services. The primary purpose of this standard is to establish minimum requirements...

American Petroleum Institute (API) Temth Edition, February 2002. 196p. This standard is based on the accumulated knowledge and experience of purchasers and manufacturers of welded, low-pressure oil storage tanks of various sizes and capacities for internal pressures not more than 15 pounds per square inch gauge. The object of this publication is to provide a purchase specification to facilitate the manufacture and procurement of such storage tank...

American Petroleum Institute (API) Temth Edition, November 1998. Addendum 2, November 2001. 240p. This standard covers material, design, fabrication, erection, and testing requirements for vertical, cylindrical, aboveground, closed- and open-top, welded steel storage tanks in various sizes and capacities for internal pressures approximating atmospheric pressure (internal pressures not exceeding the weight of the roof plates), but a higher interna...