American Petroleum Institute (API). First Edition. October 2004.
114p. This recommended practice (RP) provides guidance to the API
authorized inspector on welding inspection as encountered with
fabrication and repair of refinery and chemical plant equipment and
piping. Common welding processes, welding procedures, welder
qualifications, metallurgical effects from welding, and inspection
techniques are described to aid the inspector in fulfilling their
role implementing API 510, API 570, API Std 653 and API RP 582.
API RР 577-2004 Welding Inspection and Metallurgy (Eng)
Стандарт
- формат pdf
- размер 5.86 МБ
- добавлен 17 января 2012 г.
Смотрите также
API 510-2006 Pressure Vessel Inspection Code: In-Service Inspection, Rating, Repair, and Alteration
Стандарт- формат pdf
- размер 848.62 КБ
- добавлен 13 декабря 2011 г.
70 стр. Downstream Segment American Petroleum Institute, Ninth Edition , June 2006 General Application Coverage This inspection code covers the in-service inspection, repair, alteration, and rerating activities for pressure vessels and the pressure- relieving devices protecting these vessels. This inspection code applies to all refining and chemical process vessels that have been placed in service unless specifically excluded per 1.2.2. This incl...
API 570-2009 Piping Inspection Code: In-service Inspection, Rating, Repair, and Alteration of Piping Systems
Стандарт- формат pdf
- размер 1.03 МБ
- добавлен 08 декабря 2011 г.
78 стр. THIRD EDITION, NOVEMBER 2009 The intent of this code is to specify the in-service inspection and condition-monitoring program that is needed to determine the integrity of piping. That program should provide reasonably accurate and timely assessments to determine if any changes in the condition of piping could possibly compromise continued safe operation. It is also the intent of this code that owner-users shall respond to any inspection r...
API RP 2201 - 1995 Procedures for Welding or Hot Tapping on Equipment in Service (Eng)
Стандарт- формат pdf
- размер 215.43 КБ
- добавлен 18 января 2012 г.
American Petroleum Institute (API) Fourth Edition, September 1995. 23p. This publication covers the safety aspects to be considered when hot tapping, or when welding without hot tapping on in-service piping or equipment. It is not a substitute for job planning. A detailed, written procedure for hot tapping and welding should be prepared or reviewed before starting each job to ensure that all proper steps are taken.
API RP 572-2009 Inspection Practices for Pressure Vessels
Стандарт- формат pdf
- размер 2.53 МБ
- добавлен 08 декабря 2011 г.
63 стр. THIRD EDITION, NOVEMBER 2009 This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reasons for inspection, causes of deterioration, frequency and methods of inspection, methods of repair, and preparation of re...
API RP 572-2009 Inspection Practices for Pressure Vessels (With Annex A, B,C)
Стандарт- формат pdf
- размер 17.89 МБ
- добавлен 09 декабря 2011 г.
150 стр. c Приложениями Annex A (informative) Exchangers Annex B (informative) Towers Annex C (informative) Sample Record Forms THIRD EDITION, NOVEMBER 2009 This recommended practice (RP) covers the inspection of pressure vessels. It includes a description of the various types of pressure vessels (including pressure vessels with a design pressure below 15 psig) and the standards for their construction and maintenance. This RP also includes reason...
API Std 653-2010 Tank Inspection, Repair, Alteration, and Reconstruction
Стандарт- формат pdf
- размер 586.1 КБ
- добавлен 08 декабря 2011 г.
44 стр. FOURTH EDITION, APRIL 2009 ADDENDUM 1, AUGUST 2010 This standard covers steel storage tanks built to API 650 and its predecessor API 12C. It provides minimum requirements for maintaining the integrity of such tanks after they have been placed in service and addresses inspection, repair, alteration, relocation, and reconstruction. The scope is limited to the tank foundation, bottom, shell, structure, roof, attached appurtenances, and nozzl...
AWS D1.1/D1.1M: 2010 Structural Welding Code - Steel
Стандарт- формат pdf
- размер 19.75 МБ
- добавлен 09 декабря 2011 г.
569 стр. An American National Standard Approved by the American National Standards Institute March 11, 2010 22nd Edition This code contains the requirements Tor fabricating and erecting welded steel structures. When this code is stipulated in contract documents, conformance with all provisions of the code shall be required, except for those provisions that the Engineer (see 1.4.1) or contract documents specifically modifies or exempts. The follow...
BS EN 10246-18: 2000 Non-destructive testing of steel tubes - Part 18: Magnetic particle inspection of tube ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections
Стандарт- формат pdf
- размер 114.43 КБ
- добавлен 05 декабря 2011 г.
10 стр. The European Standard EN 10246-18:2000 has the status of a British Standard February 2000 This part of EN 10246 specifies the requirements for magnetic particle inspection of the end/bevel face at the ends of seamless and welded ferromagnetic steel tubes for the detection of laminar imperfections. This part of EN 10246 is to be used for the detection of laminar imperfections on the end/bevel face at the ends of plain end and bevelled end...