This European Standard was approved by CEN on 14 October 2004. 32p.
This document describes the basic verification tests, the testing
methods, the amount of testing and the requirements for the
qualification of wire electrodes, wires and rods for welding of
aluminium.
BS EN 14532-3: 2004 Welding consumables - Test methods and quality requirements - Part 3: Conformity assessment of wire electrodes, wires and rods for welding of aluminium alloys (Eng)
Стандарт
- формат pdf
- размер 431.74 КБ
- добавлен 25 января 2012 г.
Похожие разделы
Смотрите также
AWS A5.15-90/ASME SFA-5.14 Specification for Weld8ng Electrodes and Rods for Cast Iron (Eng)
Стандарт- формат pdf
- размер 227.49 КБ
- добавлен 10 января 2012 г.
This standard American Welding Society (AWS). 1990. 18p. This specification prescribes requirements for the classification of the following: (a) Rods for oxyfuel gas welding; (b) Electrodes for gas metal arc welding; (c) Electrodes for flux cored arc welding; (d) Electrodes for shielded metal arc welding.
AWS A5.21-80/ASME SFA-5.21 Specification for Composite Surfacing Welding Rods and Electrodes (Eng)
Стандарт- формат pdf
- размер 294.64 КБ
- добавлен 11 января 2012 г.
This standard American Welding Society (AWS). 1980. 20p. This specification prescribes requirements for composite surfacing welding rods and electrodes. The specification covers straight length bare and covered composite welding rods for use with the oxyfuel, gas tungsten arc, and atomic hydrogen welding processes.
AWS A5.9-93 / ASME SFA-5.9 Specification forbare stainless steel welding electrodes and rods. (Eng)
Стандарт- формат pdf
- размер 447.16 КБ
- добавлен 08 января 2012 г.
This standard American Welding Society (AWS). 1993. 25p. This specification prescribes requirements for the classification of bare stainless steel wire, strip, composite metal cored, and stranded welding electrodes and rods.The chromium content of these filler metals is not less than 10.5 percent and the iron content exceeds that of any other element.
BS EN 12072: 2000 Welding consumables - Wire electrodes, wires and rods for arc welding of stainless and heat-resisting steels - Classification (Eng)
Стандарт- формат pdf
- размер 358.52 КБ
- добавлен 20 января 2012 г.
This European Standard was approved by CEN on 4 September 1999. 12 p. This standard specifies requirements for classification of wire electrodes, wires and rods for gas shielded metal arc welding, gas tungsten arc welding, plasma arc welding and submerged arc welding of stainless and heat resisting steels. The classification of the wire electrodes, wires and rods is based on their chemical composition.
BS EN 14532-1: 2004 Welding consumables - Test methods and quality requirements - Part 1: Primary methods and conformity assessment of consumables for steel, nickel and nickel alloys (Eng)
Стандарт- формат pdf
- размер 599.96 КБ
- добавлен 25 января 2012 г.
This European Standard was approved by CEN on 14 October 2004. 44p. This document describes the basic verification tests, the testing methods, the amount of testing and the requirements for the qualification of welding consumables for steel, nickel and nickel alloys intended for all fields of application.
BS EN 14532-2: 2004 Welding consumables - Test methods and quality requirements - Part 2: Supplementary methods and conformity assessment of consumables for steel, nickel and nickel alloys (Eng)
Стандарт- формат pdf
- размер 450.05 КБ
- добавлен 25 января 2012 г.
This European Standard was approved by CEN on 14 October 2004. 26p. This document applies to welding consumables for which supplementary qualification is required. It contains the technical requirements to be fulfilled.
BS EN 756: 2004 Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification (Eng)
Стандарт- формат pdf
- размер 220.89 КБ
- добавлен 19 декабря 2011 г.
This European Standard was approved by CEN on 2 January 2004. 16p. This standard specifies requirements for classification of electrode-flux combinations and all-weld metal in the as-welded condition for submerged arc welding of non alloy and fine grain steels with a minimum yield strength of up to 500 MPa. Classification can be made with solid wire electrodes or tubular cored electrodes. One flux may be classified with different electrodes. The...
BS EN ISO 636: 2008 Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification
Стандарт- формат pdf
- размер 615.57 КБ
- добавлен 01 декабря 2011 г.
The text of ISO 636:2004 has been prepared by Technical Committee ISO/TC 44 Welding and allied processes of the International Organization for Standardization (ISO) and has been taken over as EN ISO 636:2008 by Technical Committee CEN/TC 121 Welding the secretariat of which is held by DIN. This European Standard was approved by CEN (EUROPEAN COMMITTEE FOR STANDARDIZATION) on 5 April 2008 This International Standard specifies requirements for clas...